Mould Lubrication Oil
RXSOL-81-1020-210Penetrating Oil A very strong cleaner, which can be used to soften up / remove baked on drying oils and Hard coke asphaltic deposition etc. It is low toxic product with an exceptional solvency power on soil & oily matter . It is minimizes the extre
Product Description
RXSOL Mould Lubrication Oil is a specially formulated industrial lubricant designed to provide effective lubrication between mould surfaces and the material being processed. It forms a thin, uniform lubricating film that helps minimize friction, sticking and material adhesion during moulding operations.
The product facilitates smooth mould release, reduces surface defects and helps maintain the cleanliness of mould surfaces. Its lubricating properties help reduce wear caused by repeated moulding cycles and contribute to improved operational efficiency.
It is suitable for industrial moulding applications where controlled lubrication and easy release of finished products are required.
Application & Usage
Areas of Application
- Industrial mould lubrication.
- Concrete moulds and formwork applications, subject to substrate compatibility.
- Precast concrete moulds.
- Cement product manufacturing.
- Industrial casting and moulding operations.
- Mould surfaces requiring lubrication and release assistance
Dosage
How to use Mould Lubrication Oil?
Step 1 - Surface Preparation
- Ensure the mould surface is clean and free from concrete deposits, dust, rust and other contaminants.
- Remove any residual hardened material before applying the lubricant.
Step 2 - Application
- Apply RXSOL Mould Lubrication Oil directly onto the mould surface using a spray gun, brush, roller or clean cloth.
- Spread evenly to form a thin, continuous lubricating film.
- Avoid excessive application and accumulation of oil in corners or depressions.
Step 3 - Moulding Operation
- Allow the applied film to distribute uniformly over the mould surface.
- Proceed with the moulding or casting operation as per the production process.
- Ensure that excess oil is removed before introducing the moulding material.
Step 4 - Maintenance
- Clean the mould after each production cycle, where necessary.
- Reapply the lubricant before the next moulding operation.
Technical Specifications
|
Parameter |
Specification |
Test Method |
|---|---|---|
|
Appearance |
Clear, homogeneous liquid |
Visual |
|
Colour |
Pale yellow to amber |
Visual |
|
Odour |
Mild petroleum odour |
Organoleptic |
|
Density @ 15°C |
0.850-0.890 g/cm³ |
ASTM D4052 |
|
Specific Gravity @ 15°C |
0.850-0.890 |
ASTM D4052 |
|
Solubility in Water |
Insoluble |
Visual |
|
Corrosive Properties |
Non-corrosive under normal application conditions |
ASTM D130 |
Notes
Key Features of Mould Lubrication Oil
- Effective Lubrication: Creates a lubricating film on mould surfaces to minimize friction.
- Easy Mould Release: Helps prevent sticking and facilitates removal of moulded products.
- Surface Protection: Helps reduce direct contact and wear between moulding surfaces.
- Reduced Surface Defects: Promotes smoother release and helps minimize surface damage.
- Operational Efficiency: Supports consistent moulding operations and reduces cleaning frequency.
- Mould Conditioning: Helps maintain mould surfaces during repeated production cycles.
Material Safety Data Sheet (MSDS)
| Product Code | RXSOL-81-1020-210 |
| Product Name | Mould Lubrication Oil |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | +91 22 2781 1318 |
| mail@rxmarine.com | |
| Website | www.rxmarine.com |
| Chemical Name | Concentration | CAS Number | EC Number | R Phrases* | Symbols |
| Naphtha (petroleum), hydrosulfurized heavy | 60-100 | 64742-82-1 | 265-185-4 | 65, 66 | Xn |
|
Hydrotreated heavy naphthenic destillate |
10-30 | 64742-52-5 | 265-155-0 | ||
| Methyl salicylate | 1-5 | 119-36-8 | 204-317-7 | 22, 36/37/38 | Xn |
| 2-(2-Butoksyethoxy)ethanol | 1-5 | 112-34-5 | 203-961-6 | R36 | Xi |
*See Section 16
|
Odour: Characteristic odour, Smells of hydrocarbon |
| Contact with skin | Wash affected area with plenty of water |
| Contaminated clothing should be laundered before reuse | |
| Contact with eyes | If substance has got into eyes, immediately wash out with plenty of water for several minutes |
| When in doubt or symptoms persist, seek medical attention | |
| Ingestion | |
| - | Do not induce vomiting because of risk of aspiration into the lungs. If aspiration is suspected obtain immediate medical attention |
| - | Give 200-300mls (half pint) water to drink |
| - | Obtain immediate medical attention |
| inhalation | |
| Remove patient to fresh air | |
| When in doubt or symptoms persist, seek medical attention | |
| General | |
| In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) (S45) |
| - | Auto-ignition point 230 deg C at 760 mm Hg |
| - | Flash point >63 deg C (CC) |
| - | Decomposition products may include carbon oxides |
| Personal Precautions | |
| Wear protective clothing as per section 8 | |
| Environmental Precautions | |
| Do not allow to enter public sewers and watercourses | |
| Clean Up Actions | |
| Soak up with inert absorbent | |
| Wash spill site with water and detergent |
| Handling | |
| The usual precautions for handling chemicals should be observed | |
| Storage | |
| Keep away from open flames, hot surfaces and sources of ignition. |
| Exposure Limits | |
| Naphtha (petroleum),hydrosulfurized heavy | |
| TLV (TWA) 275 mg/m3 (Naphtha, low boiling, hydrogen treated) | |
| Exposure controls | |
| No special precautions are required for this product | |
| Occupational exposure controls | |
|
Respiratory protection may be required under exceptional circumstances when excessive air contamination exists |
|
| Wear plastic or rubber gloves | |
| Odour: | Characteristic odour, Smells of hydrocarbon |
| Appearance | Liquid, colourless to yellow, insoluble in water |
| pH - | not applicable |
| Boiling point | 180 °C to 270 °C at 760 mm /Hg |
| Vapour density |
(air = 1) >1 |
| Insoluble in water | |
| Specific gravity | (water=1) 0.81 |
| Auto-ignition point | 230 deg C at 760 mm Hg |
| Upper explosive limit | 8 % (in air) |
| Lower explosive limit | 0.6 % (in air) |
| - | This article is considered stable under normal conditions |
| - | Keep away from naked flames, incandescent or hot surfaces |
| - | See Section 5 |
| Toxicological information | ||
| - |
No experimental data available Inhalation |
|
| Inhalation | ||
| - |
Inhalation of solvent vapours may give rise to nausea, headaches and dizziness |
|
| Contact with skin | ||
| Prolonged skin contact will result in defatting of the skin, leading to irritation, and in some cases, dermatitis | ||
| Contact with eyes | ||
| Causes irritation | ||
| Ingestion | ||
| Not regarded as a potential route of exposure. | ||
| Aspiration hazard | ||
| The ingestion of significant quantities may cause damage to lungs | ||
| Carcinogenicity | ||
| No evidence of carcinogenic effects |
| Ecotoxicity | |
| - |
This product does not contain ingredients which are classified in the EU as dangerous for the environment. |
| Mobility | |
| Persistence and Biodegradability | |
| - | Most components in this product are not readily biodegradable. |
| Bioaccumulation Potential | |
| - | Hydrocarbon solvents have the potential to bioaccumilate. |
| Other Adverse Effects | |
| - |
No environmental problems are expected when the product is used / handled correctly. In its intended use, the product will not be released into the environment. |
| Classification | |
| - | EU Waste class: 07.01 |
| Disposal considerations | |
| - | Do not discharge into drains or the environment, dispose to an authorised waste collection point |
| - | Disposal should be in accordance with local, state or national legislation |
Not classified as hazardous for transport
| Risk Phrases | |
| - | Harmful: may cause lung damage if swallowed (R65) |
| - | Repeated exposure may cause skin dryness or cracking (R66) |
| Safety Phrases | |
| - | If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label (S62) |
| - | Avoid contact with skin (S2 |
| - | Do not breathe gas (S23) |
| - | Do not breathe vapour/fumes (S23) |
| - | Do not breathe spray/mists (S23) |
|
Text of R and S phrase codes used in this safety data sheet:- R22: Harmful if swallowed; R36: Irritating to eyes; R36/37/38: Irritating to eyes, respiratory system and skin; R65: Harmful: may cause lung damage if swallowed; R66: Repeated exposure may cause skin dryness or cracking.
The information provided about the product on this Safety Data Sheet has been compiled from knowledge of the individual constituents DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable. |
Supply Locations
Mould Lubrication Oil manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of Mould Lubrication Oil at a competitive price from us. We have ready stock of Mould Lubrication Oil in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.
Need pricing or a bulk quote?
Send us the product and quantity — our team replies with a quote same day.